Below are the specs we have on file for this
machine. Please contact Machine Tools 24/7 if
you have any questions.
| Machine ID | Year | Manufacturer | Model | Control |
| 11322 | 1996 | Roundo | R-13-S | |
| | Description | Spec Values |
| Capacity: | Angle Bend Capacity (leg out 60") | 8" x 8" x 1 - 1/4" |
| | Angle Bend Capacity (leg in 50") | 3" x 3" x 1/4" |
| | T-Section (leg out 50") / (leg in 60") / (leg down 50") | WT 8" - WT 3" |
| | Flat Bar on Flat Hard Way 120" | 16" x 2-3/8" |
| | Flat Bar on Flat Hard Way 80" | 12" x 3-1/2" |
| | Flat Bar on Flat Hard Way 60" | 3" x 1/2" |
| | Flat Bar on Flat Easy 70" | 22" x 4" |
| | Square 100" / Square Tube | 8" x 8" / 16" x 16" 5/8" |
| | Round Bar 80" / Pipe Schedule 40 | 10 1/2" / 20" |
| | S & WF Beams 200" | W 36" x 210# |
| | WF Beams 200" | W 33" x 241# |
| | WF Beams 150" | W 30" x 211# |
| | Channel In & Out (60") | MC 18" x 58# C 6" |
| | Beam On X-X Axis (1,800") | W 24" x 117# W 6" |
| | Channel On X-X Axis (700") | MC 16" x 58# C 6" |
| | Solid Stock (bar or square) | 10" x 10" x 100" |
| Rolls: | Diameter of Bending Rolls | 32" |
| Motor: | Main Motor | 108 HP |
| Feeds: | Material Speed | 0 - 23 FPM |
| Dimensions: | Floor Space (L x W x H) | 218" x 155" x 168" |
| | Weight (approx) | 122,800 Lbs |
| | Equipped With |
| Additional Info.: | Hydraulically Controlled Guide Rolls - Up / Down / In & Out / Left & Right |
| | Large Selection of Spacers For Beam on Edge, Channels, Bars and Tubing |
| | Full Pendant Control |
| | Oversized Shaft, Motors & Drive (normally found on R-15-S machines 15.748") |
| | Power In-Feed Rolls 12" Diameter x 3/4" Wall |
| | Portable Hydraulic Support Roll Stand |
| | Five (5) Sets of Pipe or Tube Rolls 8", 9", 10", 12" and 20" Diameters |
| | Digital Position Indicators For Two (2) Rear Adjustable Rolls |
| | Beam-On-Edge Device With (3) Sets of Pulling Rolls (Hydraulically Powered) |
| | Set of Square / Rectangular Reversible Tubing Dies (3/8" & 1/2" Wall Tubing) |
| | Four (4) Sets of Pipe Dies With Removable Spacer (8", 9", 10", 12") Convert To OD |
| | One (1) Set 20" Pipe / OD Tubing Dies Chamfered On Oustside To |
| | - Straightening Split Beams |
| | Standard Set of Angle / Bar Rolling Dies |
| | - Grooved For Capture of Beam & Channel Flanges When Rolling The Easy Way |
| Note: | Rolls, Spacers, Dies, Hydraulic Support Stand, Etc.. Item Cost Over $650,000 New |
| | Machine Can be Purchased Separately From Dies |
| Click Here To Print Quote - | 11322 |
Click Here to Email Request Quote
TERMS: Cash or Cashiers Check with order,
and all equipment is FOB on floor from sold location unless
otherwise stated. All equipment subject to prior sales and is
exclusive of any government tax. Equipment descriptions are intended
only as a guide and their accuracy is not guaranteed. CONDITIONS:
Item(s) are sold "As Is, Where Is" unless other arrangements have
been made and conveyed in writing. There are no warranties, which
extend beyond the description on the face hereof; quotation subject
to change without notice. All agreements and/or contracts made by
sales person are subject to approval. -EQUIPMENT SAFETY: It is the
buyer's/user's responsibility to provide proper safety devices and
equipment to safeguard persons from harm resulting from any
particular use, operation or set-up, and to adequately safeguard the
equipment conform to all Federal, State and Local Government Safety
Standards and all Industrial Standards. - INDEMNIFICATION:
Buyer/User agrees to Indemnify and hold harmless Seller and
Salespersons from any and all claims or liabilities caused by or
arising from the equipment on the face hereof. All equipment quoted
is subject to prior sale. It is purchasers responsibility to verify
machine condition, specifications and pay any and all applicable
taxes.
| Manufacturer | Model | Machine ID | Machine Photos |
| Roundo | R-13-S | 11322 |  |
| Roundo | R-13-S | 11322 |  |
| Roundo | R-13-S | 11322 |  |
| Roundo | R-13-S | 11322 |  |
| Roundo | R-13-S | 11322 |  |
